Replacing Sump Pump Basement

How To Replace A Basement Sump Pump

Looking To Save Some Money? You Can Replace A Basement Sump Pump Yourself. We Give You The Steps And Show You How.

Are you ready to take charge of your basement sump pump system and replace a sump pump? If you have never done it before and never watched a plumber do it, it can be very overwhelming. Relax! It is not that hard! A sump pump is not as mysterious as you may think.

The following topics are covered in detail to help you have a successful install.

Before You Start, Get To Know Your Existing Sump Pump System

Basement Sump Pump Discharge Piping✔ Observe what is above the basement pit. A discharge system comes from the pump port up through the cover. The best discharge system will have a check valve, some elbow PVC fittings and piping that is angled to go through the top of the basement wall and outside the house.
✔ Note how the vertical discharge piping is attached to the piping from the pump port because the two will need to be separated when the sump pump is removed from the basin. Usually there is a clamped on connector or check valve. Sometimes a check valve is screwed in place. If there nothing that can be screwed or un clamped, the discharge piping will need to be cut when the pump is removed.
✔ See if there is a cover for the pit. Note how it can be removed. Most pit covers have a slot so they can be slid off. Some area of the country have high radon levels so the cover may be bolted down.
✔ Remove the cover and find out the brand and model of the sump pump.

Should I Buy The Same Brand Model For A Replacement Sump Pump?

Before replacing the sump pump in the basement, it may be time to consider a new pump brand model. Here are some helpful tips.

✔ If you are satisfied with the current brand model, buy a replacement just like it.
✔ If you are not satisfied, now is the time to consider a different brand model.
How To Pick The Best Sump Pump✔ Zoeller Pump Company manufactures their sump pumps in the United States. Each pump is tested before leaving the factory for leaks and performance capability. The Zoeller M63 and M95 have an electronic enhanced mechanical float switch. The components are completely cast iron. The warranty is extended to 5 years.
✔ Wayne Pump offers many models and pump housing types. Their pumps have been tested to run 1 million cycles without failure. The pumps are assembled in the United States with some imported parts. Their warranty for one-half horse power or larger carbon steel sump pumps is three years. Some Models have a 5 year warranty.
✔ Liberty Pumps are manufactured in the United States. They are known for their vertical magnetic float switch, and quick disconnect power cord without breaking the seal. Their housing varies from thermoplastic, aluminum to cast iron.
✔ Little Giant Pumps has long been known for its diaphragm switch; however, it has many models using cast iron housing and the vertical float switch no puncture feature. Their pumps are manufactured in the United States. They offer the most variety of models with a three year warranty.
✔ Flotec Pump uses a different style float switch which tends to fail more quickly; however with its piggyback plug this problem can be easily solved by bypassing the use of the in-built float switch and installing the external electronic switch HC6000. We are testing the installment of a Flotec sump pump using the HC6000 electronic switch. So far this setup has been running without failure since 2011. We recommend this set up. It works great and easy is to install!
✔ Check out the recommended Brands And Models.
✔ Regardless of the brand model pump purchased, it is wise to buy a new check valve as well. The check valve should be replaced every time a new sump pump is installed.

When To Replace A Sump Pump

✔ Be grateful if the current pump is still operating
✔ Look for a sunny day
✔ Set aside at least four hours if this is the first time you are replacing a sump pump. Why not do a dry run first while your sump pump is still working?
✔ Generally the float switch will fail before the pump motor; therefore check our replacement parts to see if your brand model has a replacement float switch. Generally float switches last 3 to 5 years depending upon how frequently the pump runs.

Thirteen Steps To Replacing The Sump Pump

Here are the thirteen steps for replacing a sump pump. The process is easy. The first time may take extra time, but the next time will go much faster.

  1. Unplug the existing sump pump
  2. Remove the sump basin cover.
  3. Sump Pump Replacement StepsUnscrew or loosen the end of the installed check valve closest to the pit so there are two pieces: one that goes up to the side of the basement wall and the other piece that attaches to the pump. Catch any remaining water in the pipe with a bucket. Remove the old check valve completely and replace it with a new one.
  4. Pull the old sump pump from the basin. Place the pump with the piece of the discharge pipe attached to the port in a bucket to catch draining water.
  5. Clean the basin bottom of debris including stones.
  6. Unscrew the pipe from the old pump port. Clean it if necessary. If it is impossible to remove. Buy some PVC piping Schedule 40 and a PVC pipe fitting adapter. Measure the length needed. Glue the PVC pipe to the adapter.
  7. Put a layer of plumbers tape around the inside of the replacement sump pump port. Screw the discharge pipe from the old pump into the replacement pump port or the new one made during Step 6. Remember one quarter turn beyond hand tight.
  8. Place the replacement sump pump in the basin. Align the discharge pipe with the dangling upper discharge pipe. Attach the pipe ends.
  9. Make sure the float switch is not close to the basin outer edge or near any piping to prevent hang up.
  10. Plug the pump into the electrical outlet.
  11. Test the new pump. Pour enough water into the pit to cause the float switch to activate the pump to run.
  12. Watch for leaks. If there are none and the pump ran and shut off normally. The installation is complete.
  13. Congratulate yourself for a job well done.

Watch How To Replace A Basement Sump Pump

Atlantic Drain shows and explains it well.

Conclusion

Installing a basement replacement sump pump yourself is an easy task. We highly recommend installing your own sump pump for the following reasons.

1) Knowing how and installing your own sump pumps gives more brand freedom. You are not locked into the plumber’s brand.
2) When your sump pump fails you can take immediate action rather than be at the mercy of the plumber’s schedule.
3) You can be proactive and have a replacement pump on hand. This gives you the most flexibility and ability to react to sump pump failure quickly.
4) You save money. The money you save can be used to buy an extra pump for an emergency such as pump failure.

Let us know about your sump pump replacement. What was the hardest? What surprised you? Are you glad you chose to do it yourself?

Happy Sump Pump Replacement!

Leave a Comment